The packaging is designed to protect the product from minor physical impacts during transport. Be careful to avoid effects other than these.
The packaging of the product is not water, flame and heat resistant and only moderately pressure resistant. Therefore, do not keep the box in a humid environment, out of the reach of heat-emitting equipment, or place heavy objects on it.
The package includes the device and its accessories.
Contents of the package
1 tracking device | |
1 vehicle connection cable | |
1 installation instructions |
As with mobile phones, a SIM card is required to operate the device. The device communicates with the mobile service provider's network via SIM card, SMS or mobile phone or PC applications.
You can purchase the card independently from your mobile service provider or, in the case of a software subscription, from your product distributor. If you received the SIM card from your dealer, you do not need to make any settings: the card is already set up, inserted in the device, switched on and ready for use.
If you have received the SIM card from your dealer, do not try to transfer it to another device (eg phone) and use it! The distributor (service provider) will reimburse the resulting costs or the correction of the resulting errors.
Settings for your SIM card
If you did not obtain the SIM card from your tracking device vendor, you must set it up before inserting and using it in the device, which you can do as follows.
Disable SIM card PIN and other functions
After turning off the above, insert the card into the tracking device. See the next section for instructions on how to insert the SIM card.
If you want to operate the device not only via SMS, but also e.g. If you use the software tracking service provided by your dealer, you must activate GPRS (Internet) data traffic and enter the appropriate network settings. To do this, you must send SMS messages from your phone to the phone number of the SIM card inserted in the tracking device, as shown in the table below.
The factory-set access password for the tracking device in the commands: 123456
Setting | SMS content | Device response |
---|---|---|
Turn on GPRS data traffic | gprs123456 | GPRS ok |
Setting APN name | apn123456 APN-name | apn ok |
APN names for domestic service providers:
Telenor: online or net Telekom: internet Vodafone: - in case of subscription: internet.vodafone.net - in the case of a top-up card: vitamax.internet.vodafone.net Digi: internet |
||
If your mobile network provider has not provided you with an APN username and password, you do not need to send the following SMS messages to the tracking device! | ||
APN username | apnuser123456 APN-username | apnuser ok |
APN password | apnpasswd123456 APN-password | apnpasswd ok |
Only normal size SIM cards can be used with this product. If you have a micro or nano SIM, use a card adapter!
Insert the SIM card into the device as follows:
Steps:
The device is switched on or off by inserting or removing the SIM card.
To use the device properly, it must be connected to the vehicle circuit. To do this, follow the illustration below, using the wiring harness provided with the device.
In order to operate the device and other services based on it, the distributor provides mobile and computer applications in the subscription system. The PC program is accessible via a browser at https://gpspositions.net/map/, and you can install the phone application on your phone in one of the following ways:
For Android phones
For iPhones
Use the browser on your phone to access the service (https://gpspositions.net/map/).
When you have connected the red (positive) and black (negative) wires to the corresponding poles of the vehicle power supply, wait approx. 1 minute until the appliance is put into operation. You can follow the process on the LED displays.
LED display statuses
LED | Status | |
---|---|---|
GSM (green) | 1 flash per 1 second | Connected to a network in GSM mode |
1 flash every 3 seconds | Connected to a network in GPRS mode | |
On | No GSM network connection | |
Satellites (blue) | Flashes | Connected to a satellite network |
Off | No satellite connection | |
Both LEDs flash five times quickly | Successful OBD-II connection. |
The device contains a built-in battery, which is charged or kept charged by the vehicle power supply. Battery is low - to keep the device running for a few hours after disconnecting it from the vehicle.
If the device is connected to the vehicle circuit, charging will take place automatically.
A kĂ©szĂĽlĂ©k működtetĂ©sĂ©hez a Flexcom Kft saját fejlesztĂ©sű nyomkövetĹ‘ szoftvert is biztosĂt. A működĂ©st befolyásolĂł, a kĂ©szĂĽlĂ©k telefonos SMS ĂĽzenetek Ăştján elĂ©rhetĹ‘ gyári alapfunkciĂłit lefedĹ‘, de egyben azt lĂ©nyegesen meg is haladĂł beállĂtási lehetĹ‘sĂ©geket a szoftver BeállĂtások, Parancsok Ă©s Riasztások funkciĂłi biztosĂtják.
A beállĂtások Ă©s a kiadhatĂł parancsok a kĂ©szĂĽlĂ©k tĂpusátĂłl fĂĽggenek. A konkrĂ©t lehetĹ‘sĂ©geket a szoftver a konkrĂ©t kĂ©szĂĽlĂ©khez igazĂtva bocsátja rendelkezĂ©sre. ErrĹ‘l további informáciĂłkat a szoftver használati ĂştmutatĂłjában talál.
A kĂ©szĂĽlĂ©ket más szolgáltatĂł szoftverĂ©vel is használhatja - ekkor az ebben a fejezetben leĂrtak helyett annak a szoftvernek a protokollját kell figyelembe vennie!
A Flexcom Kft asztali vagy mobiltelefonos alkalmazásának használata esetĂ©n a nyomkövetĂ©ssel kapcsolatos beállĂtási műveletek az alábbi mĂłdokon Ă©rhetĹ‘k el.
Asztali alkalmazás használata esetén:
Válassza ki a kĂvánt kĂ©szĂĽlĂ©ket a tĂ©rkĂ©pen vagy a menĂĽben.
A BeállĂtások vagy Parancsok feliratĂş gombra kattintva kiválaszthatja a kĂvánt általános beállĂtást vagy működĂ©st. |
Mobil alkalmazás használata esetén:
The factory-set access password for the tracking device in the commands: 123456
Function | Description | SMS message | Device response |
---|---|---|---|
Factory default setting | Reset the device to factory settings. |
begin123456
|
Begin Ok |
Change password | Change the factory default password (123456). |
password<old password> <new password> For example: password123456 876543 The password must be a 6-digit Arabic number. If you have subscribed to and use the reseller's software service, do not change the default factory password!
|
Password OK |
Administrator phone number | After setting the administrator phone number (s), the device only accepts calls and SMS commands from this number (s) and sends alerts to this phone number (s). Up to 5 such phone numbers can be set on the machine. After setting the first phone number, further ones can only be entered with SMS sent from this number. |
admin123456 phone number For example: admin123456 0036709876543 Use to enter the phone number country code prefix (eg 0036, Hungary).
|
Admin Ok |
Delete administrator phone number | Delete a previously set administrator phone number. |
noadmin123456 phone number For example: noadmin123456 003612345678
|
Admin Ok |
Setting time zone | The device default time zone is set to GMT + 0. This is changed (eg in the case of Hungary, the time zone is GMT + 1), as follows. |
timezone123456 value wher value: eg. +1, -2, 0 etc.). For example: time zone123456 +1 (Hungarian time zone setting)
|
Time Ok |
Query device status | Querying the operating data and status of the device. |
check123456
|
The device communicates via SMS the external power supply, battery voltage level, the status of GPS and GSM connections, etc. |
Query IMEI number | Retrieve the IMEI of the device. |
imei123456
|
The IMEI number of the device. |
Redirect messages | Forward third-party messages received on the device's SIM card to the administrator's phone (eg SMS received from the SIM card provider). |
forwardi123456 <third party phone number>
|
Forward Ok |
Switch between SMS / GPRS mode | Switch between controlling your device via SMS or an Internet connection. The factory default mode is SMS. |
GPRS123456
|
GPRS Ok |
Reduced GPRS mode | By setting it, the device switches to reduced (economy) GPRS mode 5 minutes after the vehicle is stopped. It has switched to full operation again for an alarm or to start the vehicle. |
less gprs123456 on
|
Less gprs on Ok |
Full GPRS mode | Switch back from reduced GPRS mode. |
less gprs123456 off
|
Less gprs off Ok |
Restart the device | Restart the GPS and GSM modules of the device. |
reset123456
|
Reset Ok |
You can set your device to send position data continuously under certain conditions.
Any of the auto-tracking settings discussed below can result in a series of SMS messages between the tracking device and the owner’s phone - this can have significant cost implications.
If you want to operate the device in this way, it is definitely recommended to use the service provider's software tracking service, which provides these functions - regardless of the frequency and amount of data transmissions - for a fixed monthly fee.
Function | Description | SMS message | Device response |
---|---|---|---|
Send position data at specified intervals, in specified quantities. | The device sends position messages every XXX seconds until you cancel the command. The value of the quantity (YYY) parameter can be up to 255. |
fixXXXsYYYn123456 For example: fix030s005n123456
|
Position data |
Send position data at specified intervals, without quantity limit. | A kĂ©szĂĽlĂ©k XXX másodpercenkĂ©nt YYY darab pozĂciĂł ĂĽzenetet kĂĽld. Az XXX idĹ‘intervallum minimum 20 másodperc lehet. |
fixXXXs***n123456 For example: fix030s***n123456
|
Position data |
Sending position data depending on the distance traveled. | The device can be set to send position data automatically after each distance unit traveled. The device continuously sends the position data until the command is canceled.
Before sending the command, set the device to “Send position data at specified intervals without quantity limit” mode (see previous point). |
distance123456 <distance in meters> Például: distance123456 0050 (send position data in every 50 meters).
|
Position data |
Turning off auto-tracking | Disable any of the above automatic tracking settings. |
nofix123456
|
The device has a built-in microphone and data storage on an SD card. Ambient noise and sounds listened to with the help of a microphone can be recorded on the card in the form of a sound recording. You can listen to the recordings by moving the card to your phone or computer. The device is set to tracking mode at the factory.
Function | Description | SMS message | Device response |
---|---|---|---|
Activate monitoring mode | Turn on recording. The trace is then paused and the device is switched on for approx. It records sounds that can be heard around 5 meters. |
monitor123456
|
|
Deactivate monitoring mode | Turn off recording, return to tracking mode. |
tracker123456
|
Once the device is connected to the vehicle, you have the option of stopping it remotely and preventing it from restarting.
Immediate shutdown
Speed dependent stop
Immediate remote stop of the vehicle, regardless of speed, can also cause an accident. To avoid this, the device can be set to stop the vehicle only when its speed is below 20 km / h.
Unlock vehicle
To unblock a remotely stopped vehicle, send an SMS resume123456 to the device.
Description | SMS message | Device response |
---|---|---|
The device sends an alarm to the phone when the vehicle is started / stopped. This alarm is disabled at the factory. |
Bekapcsolás: acc123456 Content of the alarm message: ACC on!” Turning off: noacc123456
|
ACC set Ok or NoACC set Ok |
Description | SMS message | Device response |
---|---|---|
You can set an alarm in case the battery level drops too low. When turned on, the device sends 2 alarms at 15-minute intervals when the device battery voltage is approx. It drops below 3.5V. The setting is activated by factory default. |
Turning on: lowbattery123456 on Content of the alarm message: „Low battery <vehicle position>”. Turning off: lowbattery123456 off
|
Description | SMS message | Device response |
---|---|---|
If the device is connected to an external power source (eg vehicle), you can set an alarm if it is switched off. The device sends the message to the administrator telephones repeated every 3 minutes until the power supply is switched off or the alarm is deactivated from one of the telephones. The alarm is switched off at the factory. |
Turning on: extpower123456 on Content of the alarm message: „Power alarm <vehicle position>”. Turning off: extpower123456 off
|
Description | SMS message | Device response
|
---|---|---|
You can set the device to send an alert to the administrator phones if the satellite connection is lost. The alarm is switched off at the factory. |
Turning on: gpssignal123456 on Content of the alarm message: „No gps <vehicle position>”. Turning off: gpssignal123456 off
|
Description | SMS message | Device response |
---|---|---|
If the device (vehicle) has been stationary for 3-10 minutes and the device is connected to the satellite network, you can set it to send an alarm to the administrator phones when it moves. |
Turning on: move123456 XXXX where XXXX = displacement in meters. For example: move123456 0100 in case of device alarm sends if the amount of displacement exceeded 100 meters. The content of the alarm message: "Move <vehicle position>". Turning off: nomovel123456
|
Description | SMS message | Device response |
---|---|---|
You can set the device to send an SMS alert if the vehicle speed exceeds the specified limit. The speed limit must be entered in the form XXX, if less than 100, the leading zero must also be written (eg 070). |
Turning on: speed123456 sebességhatár For example: speed123456 070 A riasztó üzenet tartalma: „Speed 70! <vehicle position>” Turning off: nospeed123456
|
Description | SMS message | Device response |
---|---|---|
Send an alarm to the phone if the vehicle moves, overturns or is hit. The sensitivity of the sensor can be adjusted in 3 levels. |
To set the sensitivity, send the following in advance SMS message to the device: **sensitivity123456 X** where - X = 1 (alarm even in case of weak effect) - X = 2 (alarm only in case of moderate effect) - X = 3 (alarm only in case of strong effect) and after this Turning on: shock123456 Content of the alarm message: „Sensor alarm <vehicle position>” Turning off: noshock123456
|
Tracking easily and efficiently