User Tools

Site Tools


en:devices:manufacturers:ningmore:area:car:lk720a:manual:guide:full

User's guide

Transport and storage

The packaging is designed to protect the product from the usual physical effects during transport. Be careful to avoid effects other than these.

The packaging of the product is not water, flame and heat resistant and only moderately pressure resistant. Therefore, do not store the package in a humid environment, within the scope of heat-emitting equipment, or place heavy objects on it.

 

Commissioning

The package includes the device and its accessories.

Unpacking

Package

  1. Open the box.
  2. Remove the product and its accessories.

Contents of the package

IK720A tracking device 1 tracking device
Installation instructions 1 installation instructions

Preparing the SIM card

As with mobile phones, a SIM card is required to operate the device. The device communicates with the mobile service provider's network via SIM card, SMS or mobile phone or PC applications.

You can purchase the card independently from your mobile service provider or, in the case of a software subscription, from your product distributor. If you received the SIM card from your dealer, you do not need to make any settings: the card is already set up, inserted in the device, switched on and ready for use.

If you have received the SIM card from your dealer, do not try to transfer it to another device (eg phone) and use it! The distributor (service provider) will reimburse the resulting costs or the correction of the resulting errors.

Settings for your SIM card

If you did not obtain the SIM card from your tracking device vendor, you must set it up before inserting and using it in the device, which you can do as follows.

Disable SIM card PIN and other functions

  1. Insert the SIM card in your phone.
  2. Among the setting functions of the phone
  3. turn off the PIN code request, auto-reply and call forwarding options.

After turning off the above, insert the card into the tracking device. See the next section for instructions on how to insert the SIM card.

 

Setting up data traffic

If you want to operate the device not only via SMS, but also e.g. If you use the software tracking service provided by your dealer, you must activate GPRS (Internet) data traffic and enter the appropriate network settings. To do this, you need to send SMS messages from your phone to the phone number of the SIM card inserted in the tracking device, as shown in the table below.

The factory-set access password for the tracking device in the commands: 123456

Setting SMS message Device response
Turn on GPRS data traffic gprs123456 GPRS ok
Enter the APN name apn123456(space)APN-name apn ok
APN names for domestic service providers: Telenor: online or net
Telekom: internet
Vodafone:
- in case of subscription: internet.vodafone.net
- in the case of a top-up card: vitamax.internet.vodafone.net
Digi: internet
If your mobile network provider has not provided you with an APN username and password, you do not need to send the following SMS messages to the tracking device!
APN username apnuser123456(space)APN-username apnuser ok
APN password apnpasswd123456(space)APN-password apnpasswd ok

 

Inserting the SIM card

Only standard size SIM cards can be used with this product. If you have a micro or nano SIM, use a card adapter!

Insert the SIM card into the device as follows:

A SIM kártya behelyezése

Application installation, access

In order to operate the device and other services based on it, the distributor provides mobile and computer applications in the subscription system. The PC program is accessible via a browser at https://gpspositions.net/map/, and you can install the phone application on your phone in one of the following ways:

For Android phones

  1. Open the Google Play app on your phone.
  2. Search for “Flexcom” or “Flexcom tracking” on Google Play.
  3. Install the tracking application.



or

  1. Scan the QR code shown here with your phone.
  2. Open the web address decoded from this.
  3. Install the Flexcom tracking application.




For iPhones

Use the browser on your phone to access the service (https://gpspositions.net/map/).

 
 

Using the product

User Interface

The device does not have a traditional user interface (eg on / off button). LED indicators inform the user about its operation and status. The displays are on the printed circuit board - so they are only visible when the cover is removed. Kezelő felület

LED display statuses

Signal Meaning
Green light stays on No GSM / GPRS connection
Green light flashes Connected to a mobile network
Blue light stays on No satellite connection
Blue light flashes Connected to a satellite network

Installation

The device must be connected to an external power source (eg vehicle battery) as shown below:

Installation

The device's own battery is used to bridge the short-term disconnection time from an external power source. It is charged during normal operation.

Normal operation of the device

The device can be operated in the following ways:

  1. using the software service provided by the distributor and the SIM card together, in addition to the software service provided by the distributor but using his own SIM card, or
  2. without the service provider's software service, with your own SIM card.

The service provider provides a SIM card for the tracking device only if you subscribe to the software service. In the case of unsolicited use of the software, the user must provide the appropriate card with a data traffic limit (also).

With Distributor Software and SIM Card

In this case, you can receive the device in the ready state, no further settings are required to use it.

Separate software is available for setting or adjusting the operating parameters of the device, for retrieving information or for using more advanced services (eg map route display, waiting and travel points, diagrams, timetable, etc.). This is provided by the distributor in the form of a downloadable application on a desktop and tablet browser on an Android mobile phone as part of a subscription system.

To use the software, an active internet connection is required on your device (mobile phone, computer).

The software stores and processes the data sent by the tracking device to the service provider's center, from which the graphical and textual information is generated. Using the software triggers (sometimes very expensive) SMS and voice call communication with the device and provides tracking and security services that go well beyond the basic functions of the device.

After launching the application in a browser or phone:

  1. In the login window, enter the username and password you received in the email from the distributor or registered on its website.
  2. In the interface that appears, select Help and review the information for using the software.
  3. Software management information is available in its help.

With Distributor software but with own SIM card

After setting up and inserting the SIM card as described in the setup chapter, you must register the card. To do this, contact your software service provider (device vendor). From now on, the operation of the device is the same as described in the previous chapter.

Without software, with own SIM card

If you have subscribed to the reseller's software service, DO NOT use the standalone SMS communication method because

  • redundant (the software has all the functions needed for tracking and settings),
  • the software provider charges a separate fee for the possible elimination of possible operational anomalies caused by SMS commands,
  • if you use your own SIM card in the device, SMS will incur extra costs,
  • if you use your service provider's SIM card, your service provider will reimburse you for the cost of the SMS.

If you do not use (have not subscribed) to the software service provided by the dealer, you can only use the basic functions of the device - by sending SMS messages from your mobile phone to the phone number of the device's SIM card.

 

Setting options via the software

When using the desktop or mobile application of Flexcom Kft, the setup operations related to tracing can be accessed in the following ways.

The settings and commands that can be issued depend on the type of device. See the rest of this guide for information on options for this device.

When using a desktop application:

Select the desired device on the map or in the menu.

Click the Settings or Commands button to select the general setting or behavior you want.
Commands and settings for a desktop application

When using a mobile application:

From the application menu, select Map. Selecting Map option
Switch to the Tools panel. Switching to the Tools panel
Find your device in the list of devices and tap the Setup icon next to the ID. Selecting Setup
Select the desired setting or, when sending a command, select Commands. Select function

 

Control the device with SMS commands sent from a mobile phone

The factory-set access password for the tracking device in the commands: 123456

 

General settings

Function Description SMS message Device response
Change password Change the factory default password (123456).

password<old password> <new password>

Example: password123456 876543
The password must be a 6-digit Arabic number.

If you have subscribed to and use the reseller's software service, do not change the default factory password!

Password OK
Administrator phone number After setting the administrator phone number (s), the device only accepts calls and SMS commands from this number (s) and sends alerts to this phone number (s). Up to 5 such phone numbers can be set on the machine. After setting the first phone number, further ones can only be entered with SMS sent from this number.

admin123456 phone number

Example: admin123456 0036709876543
When entering the telephone number, use 
the country code prefix (eg 0036, Hungary).

Admin Ok
Delete administrator phone number Delete a previously set administrator phone number.

noadmin123456 phone number

Example: noadmin123456 003612345678

Admin Ok
Setting time zone The device default time zone is set to GMT + 0. This is changed (eg in the case of Hungary, the time zone is GMT + 1), as follows.

timezone123456 value (where value: érték pl. +1, -2, 
0 etc.).

Example: timezone123456 +1 (Hungarian time zone
setting)

Time Ok
Set the upload frequency If you use the service provider's software service, the device sends data to the central server at specified intervals. You can set the sending frequency as follows:

upload123456 időköz (másodperc)
Example: upload123456 60 (sending data every minute)

Upload Ok
Sleep mode In normal mode, the device switches to sleep mode after 10 minutes of inactivity and inactivity to save energy. It switches back to active mode for any SMS message or move. Sleep mode can also be turned on or off via SMS:

Activate: sleep123456
Deactivate:nosleep123456

Sleep Ok or Nosleep Ok.
Restart the device Restart the GPS and GSM modules of the device.

rst

Restart Ok
Factory default setting Reset the device to factory settings.

format

-

 

Query the position of the device

Description SMS message Device response
At the command, the device returns a Google Map link, which, when clicked (or tapped), displays the map with the device's indication on it.

G123456#

Device information

 
 
 
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.