Felhasználói eszközök

Eszközök a webhelyen


en:devices:manufacturers:teltonika:area:car:fmb140:manual:guide:full

User's guide

Transport and storage

The packaging is designed to protect the product from minor physical impacts during transport. Be careful to avoid effects other than these.

The packaging of the product is not water, flame and heat resistant and only moderately pressure resistant. Therefore, do not keep the box in a humid environment, out of the reach of heat-emitting equipment, or place heavy objects on it.

 

Commissioning

The package includes the device and its accessories.

Unpacking

Csomag

  1. Open the tray.
  2. Remove the appliance and its accessories.

Contents of the package
FMB140 tracking device 1 tracking device
Electrical network and communication cable Electrical network and communication cable
Installation instructions 1 installation instructions

Preparing the SIM card

As with mobile phones, a SIM card is required to operate the device. The device communicates with the mobile service provider's network via SIM card, SMS or mobile phone or PC applications.

You can purchase the card independently from your mobile service provider or, in the case of a software subscription, from your product distributor. If you received the SIM card from your dealer, you do not need to make any settings: the card is already set up, inserted in the device, switched on and ready for use.

If you have received the SIM card from your dealer, do not try to transfer it to another device (eg phone) and use it! The distributor (service provider) will reimburse the resulting costs or the correction of the resulting errors.

Settings for your SIM card

If you did not obtain the SIM card from your tracking device vendor, you must set it up before inserting and using it in the device, which you can do as follows.

Disable SIM card PIN and other functions

  1. Insert the SIM card in your phone.
  2. Among the setting functions of the phone
  3. turn off the PIN code request, auto-reply and call forwarding options.

After turning off the above, insert the card into the tracking device. See the next section for instructions on how to insert the SIM card.

 

Setting up data traffic

In the case of your own SIM card, to communicate with the device, you need to connect it to the GSM network and set up data traffic. To do this, you must send SMS messages from your phone to the phone number of the SIM card inserted in the tracking device, as shown in the table below.

The factory-set access password for the tracking device in the commands: 123456

Setting SMS
Setting APN-name setparam 2001:<APN-name>
APN names for domestic service providers: Telenor: online or net
Telekom: internet
Vodafone:
- in case of subscription: internet.vodafone.net
- in the case of a top-up card: vitamax.internet.vodafone.net
Digi: internet
If your mobile network provider has not provided you with an APN username and password, you do not need to send the following SMS messages to the tracking device!
APN username setparam 2002:<APN-username>
APN password setparam 2003:<APN-password>
Server settings setparam 2004:<szerver domain név> setparam 2005:<port szám> setparam 2006:<protocol>, where protocol 0:TCP, 1:UDP
Example The above instructions can be sent to the device individually or in a single SMS: setparam 2001:internet;2002:pistike;2003:pistike1986;2004:szolgaltato.hu;2005:15423;2006:0;
More information: https://teltonika-gps.com/product
Application for setup: https://wiki.teltonika-gps.com/view/Teltonika_Configurator_versions
Jelszó: 5555

 

Inserting the SIM card and battery

Only micro-sized SIM cards can be used with this product. The card can only be inserted or removed with the device switched off (disconnected from the external power supply, excluding the internal battery) - otherwise the card may be damaged. If you have a nano type SIM card, use a card adapter!

Insert the SIM card into the device as follows:

When replacing cards, remove the battery first after removing the device cover. When connected to a power source (external or internal battery), the device turns on automatically.

Inserting the SIM card and battery

Steps:

  1. Unclip the back of the device.
  2. Insert the card.
  3. Insert the battery.
  4. Snap the cover back on.

Installing the device

By extending the connecting cable (professionally), the device can be placed anywhere inside the vehicle (protected from environmental influences), usually in the passenger compartment of the vehicle (eg under the instrument panel).

Cable distribution, installation

Installation

Application installation, access

In order to operate the device and other services based on it, the distributor provides mobile and computer applications in the subscription system. The PC program is accessible via a browser at https://gpspositions.net/map/, and you can install the phone application on your phone in one of the following ways:

For Android phones

  1. Open the Google Play app on your phone.
  2. Search for „Flexcom” or „Flexcom tracking” on Google Play.
  3. Install the tracking application.



or

  1. Scan the QR code shown here with your phone.
  2. Open the web address decoded from this.
  3. Install the Flexcom tracking application.




For iPhones

Use the browser on your phone to access the service (https://gpspositions.net/map/).

 
 

Using the product

User interface

The device does not have a traditional user interface, its operation is indicated by LED displays.

User interface

LED display statuses

Status LED

Signal Meaning
Flashes every 1 second Normal mode
Flashes every 2 seconds Sleep mode
Flashes quickly for a short time Data traffic
Not lit The device does not work or is being switched on

Navigation LED

Signal Meaning
Constantly lit No satellite connection
Flashes every 1 second Satellite connection on
Not lit No satellite connection because the device is not working or in sleep mode
Keeps flashing fast The device's firmware is being updated

CAN status LED

Signal Meaning
Constantly lit Malfunction (program or wire error)
Keeps flashing fast Reading vehicle data
Not lit Connection error or CAN processor is in sleep mode

Charging the internal battery

The device also has a built-in internal battery, which ensures short-term use and transition when disconnected from the external power source. During normal operation, the internal battery is charged by the vehicle's power source (battery) or (charged with overcharge protection).

Switching on and off

The device turns on automatically when it receives power when a charged internal battery is inserted and / or connected to the vehicle circuit. Its operation occurs when the external and internal power supply connections are disconnected / exhausted. When switched on, the device automatically searches for connections to the GSM / GPRS network and satellites. The LED displays inform about the process and the result.

Normal operation of the device

The device can be operated in the following ways:

  1. using the software service provided by the distributor and the SIM card together, in addition to the software service provided by the distributor but using his own SIM card, or
  2. without the service provider's software service, with your own SIM card.

The service provider provides a SIM card for the tracking device only if you subscribe to the software service. In the case of unsolicited use of the software, the user must provide the appropriate card with a data traffic limit (also).

With Distributor Software and SIM Card

In this case, you can receive the device in the ready state, no further settings are required to use it.

Separate software is available for setting or adjusting the operating parameters of the device, for retrieving information or for using more advanced services (eg map route display, waiting and travel points, diagrams, timetable, etc.). This is provided by the distributor in the form of a downloadable application on a desktop and tablet browser on an Android mobile phone as part of a subscription system.

To use the software, an active internet connection is required on your device (mobile phone, computer).

The software stores and processes the data sent by the tracking device to the service provider's center, from which the graphical and textual information is generated. Using the software triggers (sometimes very expensive) SMS and voice call communication with the device and provides tracking and security services that go well beyond the basic functions of the device.

After launching the application in a browser or phone:

  1. In the login window, enter the username and password you received in the email from the distributor or registered on its website.
  2. In the interface that appears, select Help and review the information for using the software.
  3. Software management information is available in its help.

With Distributor software but with own SIM card

After setting up and inserting the SIM card as described in the setup chapter, you must register the card. To do this, contact your software service provider (device vendor). From now on, the operation of the device is the same as described in the previous chapter.

Without software, with own SIM card

If you have subscribed to the reseller's software service, DO NOT use the standalone SMS communication method because

  • redundant (the software has all the functions needed for tracking and settings),
  • the software provider charges a separate fee for the possible elimination of possible operational anomalies caused by SMS commands,
  • if you use your own SIM card in the device, SMS will incur extra costs,
  • if you use your service provider's SIM card, your service provider will reimburse you for the cost of the SMS.

If you do not use (have not subscribed) to the software service provided by the dealer, you can only use the basic functions of the device - by sending SMS messages from your mobile phone to the phone number of the device's SIM card.

 

In addition, it is possible to query or change the device settings using a computer (Windows 7, 8, 10) and the Teltonika Configurator software. Further information on the above can be found on the manufacturer's website:

Setting options via the software

When using the desktop or mobile application of Flexcom Kft, the setup operations related to tracing can be accessed in the following ways.

The settings and commands that can be issued depend on the type of device. See the rest of this guide for information on options for this device.

When using a desktop application:

Select the desired device on the map or in the menu.

Click the Settings or Commands button to select the general setting or behavior you want.
Commands and settings for a desktop application

When using a mobile application:

From the application menu, select Map. Selecting Map option
Switch to the Tools panel. Switching to the Tools panel
Find your device in the list of devices and tap the Setup icon next to the ID. Selecting Setup
Select the desired setting or, when sending a command, select Commands. Select function

 
 
Ön beleegyezik abba, hogy a weboldal az optimális működéséhez szükséges adatokat tárolja az Ön jelenleg használt eszközén (sütik). Egyben kijelenti, hogy elolvasta és elfogadja az adatvédelmi tájékoztatóban foglaltakat - ha mégsem, kérjük, hagyja el a weboldalt.