The packaging is designed to protect the product from the usual physical effects during transport. Be careful to avoid effects other than these.
The packaging of the product is not water, flame and heat resistant and only moderately pressure resistant. Therefore, do not keep the box in a humid environment, within the range of heat emitting equipment, or place heavy objects on it.
The package consists of a box containing the device and its accessories.
|1 tracking device
|Carrying case and SIM devices
|1 USB cable
|1 Installation instructions
As with mobile phones, a SIM card is required to operate the device. The device communicates with the mobile service provider's network via SIM card, SMS or mobile phone or PC applications.
You can purchase the card independently from your mobile service provider or, in the case of a software subscription, from your product distributor. If you received the SIM card from your dealer, you do not need to make any settings: the card is already set up, inserted in the device, switched on and ready for use.
If you have received the SIM card from your dealer, do not try to transfer it to another device (eg phone) and use it! The distributor (service provider) will reimburse the resulting costs or the correction of the resulting errors.
Settings for your SIM card
If you did not obtain the SIM card from your tracking device vendor, you must set it up before inserting and using it in the device, which you can do as follows.
Disable SIM card PIN and other functions
After turning off the above, insert the card into the tracking device. See the next section for instructions on how to insert the SIM card.
If you want to operate the device not only via SMS, but also e.g. If you use the software tracking service provided by your dealer, you must activate GPRS (Internet) data traffic and enter the appropriate network settings. To do this, you need to send SMS messages from your phone to the phone number of the SIM card inserted in the tracking device, as shown in the table below.
The factory-set access password for the tracking device in the commands: 123456
|Turn on GPRS data traffic
|Enter the APN name
|APN names for domestic service providers in Hungary:
Telenor: online vagy net
- in case of subscription: internet.vodafone.net
- in the case of a top-up card: vitamax.internet.vodafone.net
|If your mobile network provider has not provided you with an APN username and password, you do not need to send the following SMS messages to the tracking device!
Only standard size SIM cards can be used with this product. If you have a nano or micro SIM, use a card adapter.
Insert the SIM card into the device as follows:
You can place the device on any magnetizable metallic surface, either inside or outside the passenger compartment (eg. chassis).
In order to operate the device and other services based on it, the distributor provides mobile and computer applications in the subscription system. The PC program is accessible via a browser at https://gpspositions.net/map/, and you can install the phone application on your phone in one of the following ways:
For Android phones
Use the browser on your phone to access the service (https://gpspositions.net/map/).
The device does not have a traditional user interface (eg on / off button). An LED indicator informs the user about its operation and status. In addition, only the charger connector, the SIM card slot and a carrying strap can be connected on its surface.
LED display statuses
|No mobile network connection
|Connected to a mobile network
|No satellite connection
|Connected to a satellite network
The device is powered by a built-in battery, which needs to be charged at different intervals depending on the intensity of use. Your phone's charger is suitable for charging, but you can also use the USB connection of a computer or energy bank.
The appropriate USB charging cable is included with the device. It is connected to the tracking device via a MICRO USB connector - if you do not use the factory cable, make sure that it is type-compliant!
Charging takes 6-8 hours, during which the LED indicator lights up red. When the device is fully charged, the light turns off.
When the battery is fully charged, disconnect the charging cable. The device does NOT have overcharge protection, so keeping it on a long-term or continuous charger (eg connecting to a vehicle battery) will shorten the life of the device or, in worse cases, damage it. For the device with a voltage of 5V 1 Use a charger that provides current. Chargers with a higher capacity can damage the battery.
The device switches on automatically when you insert the SIM card, and switches it off when you remove it. It does not have a separate on / off button.
The device is set at the factory to be so-called at rest. Switches to â€śsleepâ€ť mode. In this state, its operating time is about 45 days. It switches from sleep mode to operating mode (â€śwakeâ€ť) in the event of external influences (eg movement, vibration).
For use via software, the operating time also depends on how the data transmission frequency of the device has been determined (eg 10 seconds, 1 minute, 5 minutes, 1 hour, etc.). For example:
If the device is operated with SMS commands, the operating time is affected by the frequency of issuing the commands (ie forcing the device to respond).
ď»żWhen using the desktop or mobile application of Flexcom Kft, the setup operations related to tracing can be accessed in the following ways.
The settings and commands that can be issued depend on the type of device. See the rest of this guide for information on options for this device.
When using a desktop application:
Select the desired device on the map or in the menu.
Click the Settings or Commands button to select the general setting or behavior you want.
When using a mobile application:
|From the application menu, select Map.
|Switch to the Tools panel.
|Find your device in the list of devices and tap the Setup icon next to the ID.
|Select the desired setting or, when sending a command, select Commands.
The factory-set access password for the tracking device in the commands: 123456
|You can also switch the device on and off from your phone without moving the SIM card.
|Administrator phone number
|After setting the administrator phone number (s), the device only accepts calls and SMS commands from this number (s) and sends alerts to this phone number (s). Up to 5 such phone numbers can be set on the machine. After setting the first phone number, further ones can only be entered with SMS sent from this number.
admin123456 phone number PĂ©ldĂˇul: admin123456 0036709876543 Use to enter the phone number country code prefix (eg 0036, Hungary).
|Delete administrator phone number
|Delete a previously set administrator phone number.
noadmin123456 phone number For example: noadmin123456 003612345678
|Set time zone
|The device's default time zone is set to GMT + 0. This is changed (eg in the case of Hungary, the time zone is GMT + 1), as follows.
timezone123456 value (where value e.g. +1, -2, 0 etc). PĂ©ldĂˇul: timezone123456 +1 (Hungarian time zone setting)
|Turn GPRS mode on and off
|The GPRS data transfer mode is switched off by default in the device (GSM mode is active). If you use tracking software, the GPRS mode must be turned on.
If you have purchased the device with a software service subscription from the dealer, the GPRS mode is already activated!
Turning on SMS: gprs123456 Turning off SMS: nogprs123456
|GPRS Ok or NOGPRS Ok
|Call the phone number of the device's SIM card from your phone. After receiving the call, the device interrupts it and then sends the data back in an SMS message: latitude and longitude, current speed, time and link, which, when clicked / tapped, will display the device's indicator on the Google map in our phone's browser.
If the device cannot connect to GPS satellites (eg inside a building or in another shaded area), use the cell information of the GSM transmission towers to determine its position (LBS, Location Based Service). Its accuracy depends largely on the distance from the towers and the mobile network coverage.
|or LBS-based positioning
The device has a built-in microphone and data storage on an SD card. The ambient noise and sounds listened to with the help of the microphone can be recorded on the card in the form of a sound recording. You can listen to the recordings by moving the card to your phone or computer. The device is set to tracking mode at the factory.
|Activate eavesdropping mode
|Turn on recording. The trace is then paused and the device is switched on for approx. It records sounds that can be heard around 5 meters.
|Deactivate eavesdropping mode
|Turn off recording, return to tracking mode.
The device - e.g. to save energy, you can switch it to sleep mode. There are two versions of sleep mode:
In sleep mode, the satellite communication is paused, the mobile network connection operates at a basic level.
Activation in timed mode: sleep123456 time Activation in "shock" mode: sleep123456 shock Deactivate any sleep mode: sleep123456 off
|Sleep time ok, Sleep shock ok or Sleep off ok
|You can set the device to send an SMS alert if the vehicle speed exceeds the specified limit. The speed limit must be given in the form XXX, if less than 100, the leading zero must also be written out (eg 070).
Turning on: speed123456 sebessĂ©ghatĂˇr For example: speed123456 070 Content of the alarm message: â€žSpeed alarm!â€ť Turning off: nospeed123456
|Speed Ok or Nospeed Ok
|Send an alarm to the phone when the device is moved / shocked / shaken. For this to work, the device must be at rest for at least 5 minutes before exposure.
Turning on: shock123456 Content of the alarm message: â€žSensor alarmâ€ť Turning off: noshock123456
|Shock OK or Noshock Ok
|You can set an alarm in case the battery level drops too low.
Turning on: lowbatsms123456 on Turning off: lowbatsms123456 off
|â€ślowbat sms onâ€ť or â€ślowbat sms offâ€ť
Tracking easily and efficiently