Tartalomjegyzék

User's guide

User's guide

Transport and storage

The packaging is designed to protect the product from the usual physical effects during transport. Be careful to avoid effects other than these.

The packaging of the product is not water, flame and heat resistant and only moderately pressure resistant. Therefore, do not store the package in a humid environment, within the scope of heat-emitting equipment, or place heavy objects on it.

Commissioning

The package consists of a box containing the device and its accessories.

Unpacking

Open the box.
Remove the product.
Remove the retaining insert to protect the device.
Remove the accessories.

**Contents of the package**
1 tracking device	1 wall mount	1 USB charging cable	1 magnet	1 velcro	1 installation instructions

Preparing the SIM card

As with mobile phones, a SIM card is required to operate the device. The device communicates with the mobile service provider's network via SIM card, SMS or mobile phone or PC applications.

You can purchase the card independently from your mobile service provider or, in the case of a software subscription, from your product distributor. If you received the SIM card from your dealer, you do not need to make any settings: the card is already set up, inserted in the device, switched on and ready for use.

If you have received the SIM card from your dealer, do not try to transfer it to another device (eg phone) and use it! The distributor (service provider) will reimburse the resulting costs or the correction of the resulting errors.

Settings for your SIM card

If you did not obtain the SIM card from your tracking device vendor, you must set it up before inserting and using it in the device, which you can do as follows.

Disable SIM card PIN and other functions

Insert the SIM card in your phone.
Among the setting functions of the phone
turn off the PIN code request, auto-reply and call forwarding options.

After turning off the above, insert the card into the tracking device. See the next section for instructions on how to insert the SIM card.

Setting up data traffic

If you want to operate the device not only via SMS, but also e.g. If you use the software tracking service provided by your dealer, you must activate GPRS (Internet) data traffic and use the appropriate network settings if you use your own SIM card. To do this, you must send SMS messages from your phone to the phone number of the SIM card inserted in the tracking device, as shown in the table below.

Before sending the instructions in the table below from your phone to the phone number of the device's SIM card, set the administrator's phone number on the device in a preliminary SMS.

Send an SMS from your phone to the phone number of the device with the following content: password,sos1,phone-number#
Example: 123456,sos1,06209876543

All other commands sent via SMS will only be received and executed. Always use lowercase letters in SMS messages and do not leave spaces anywhere!

Setting	SMS	Device response
Setting APN	apn,apn-name,user,<username>,pd,<password>#	Ok
Setting APN	APN names for domestic service providers: Telenor: online or net Telekom: internet Vodafone: - in case of subscription: internet.vodafone.net - in the case of a top-up card: vitamax.internet.vodafone.net Digi: internet
	username: the APN username provided by the service provider. If not, it should be omitted.
	password: APN password provided by the service provider. If not, it should be omitted.

Inserting the SIM card

Only micro-sized SIM cards can be used with this product. If you have a nano SIM, use a card adapter.

Insert the SIM card into the device as follows:

Steps:

Make sure the appliance is switched off.
Open the cover of the SIM card slot.
Insert the card into the slot in the correct position.
Close the protective cover.

Charging the battery

The device has a built-in battery that can be charged via the USB port. Your phone charger is suitable for charging, but you can also use the USB connection of a computer or energy bank.

The corresponding USB charging cable is supplied with the device by the manufacturer. This is connected to the device via a MICRO USB connector - if you do not use the factory cable, make sure that it is type-compliant!

The charge level is indicated by a four-member LED indicator.

Charge the device for at least 8 hours before using it for the first time!

When the battery is fully charged (all four LEDs are lit), disconnect the charging cable. The device does NOT have overcharge protection, so prolonged or continuous charging will shorten the life of the device or, in worse cases, damage it.

Use a charger that supplies 2 A to the device at a voltage of 5 V. Chargers with a higher capacity can damage the battery.

It is recommended to fully discharge the battery every 3 months and then recharge it! Do not use the device while charging, this applies especially to the energy bank function!

Application installation, access

In order to operate the device and other services based on it, the distributor provides mobile and computer applications in the subscription system. The PC program is accessible via a browser at https://gpspositions.net/map/, and you can install the phone application on your phone in one of the following ways:

For Android phones

Open the Google Play app on your phone.
Search for “Flexcom” or “Flexcom tracking” on Google Play.
Install the tracking application.

or

Scan the QR code shown here with your phone.
Open the web address decoded from this.
Install the Flexcom tracking application.

For iPhones

Use the browser on your phone to access the service (https://gpspositions.net/map/).

Using the product

User Interface

The connectors and controls of the device are located at both ends, under a protective cover, and on one side of the microphone.

(1) Lamp
(2) SIM slot
(3) Microphon
(4) On / off switch button
(5) Speaker
(6) Battery level display
(7) Micro USB (for input charging)
(8) USB output (for outgoing charging)

Status of LED displays showing GPS / GSM connections

LED indicators showing the status of network connections are located next to the SIM card slot, under the protective cover.

**Status of LED displays**
Color	Function	Slow flashing	Quick flashing	Not lit
Blue	GPS connection	Searching	Successful	No
Yellow	GSM connection	Searching	Successful	No

Turning on and off

You can switch the device on and off with the power key.

Turning on

If it is not already inside, insert the SIM card in the device.
Press and hold the button for approx. 3-5 seconds.
The device beeps successfully with three beeps.

Turning off

Press and hold the button for approx. 3-5 seconds.
The blue and yellow LEDs light up, then approx. They go out after 15 seconds - the device is switched off.

Operating time

The device works continuously after switching on. Its operating time depends on the usage mode and related settings:

With GSM network connection on and position transmission interval of 10 minutes, the standby time is 30 days and the communication time is 60-80 hours.
If the GSM network is switched off (eg if the device is used only as an energy bank), the standby time increases to 3 months.

Operating modes

The device can be operated in the following ways:

energy bank,
alarm (eg movement, door opening detection), tracking or
lamp

Powerbank The device can be used as an energy bank to charge other devices (eg mobile phones). Plug the included USB cable into the power bank output, connect the devices to be charged to the appropriate cable ends. It is not necessary to switch on the device to charge other devices. The power bank function is only used when the device battery is sufficiently charged. If only one of the charge level LEDs is lit, charge the battery before use.
Alarms Different alarm functions can be set on the device for different types of events. When the event occurs, the device sends an SMS message to the administrator's phone number, or you can also sound beeps on your speaker. Beep The operation of the beeps can be switched on or off with the following SMS commands: Turning on Send hon# (horn on) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. Turning off Send hoff# (horn off) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. You can set the alarm delay with the following SMS command: ntim,x# where x is the delay time in seconds. Magnetic detection The device can also be used to detect the opening of a door (or any door and window) using the included wall mount and magnet. Mount the wall bracket on the wall next to the door. Mount the magnet on the door. Slide the appliance into the wall mount from above. To activate or deactivate the magnetic opening detection mode, the following SMS commands must be sent to the device: Turning on Send the command don# (door on) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. Turning off Send the command doff# (door off) to the phone number of the device via SMS. If the device has received and executed the command, confirm it by sending an SMS with OK. Motion, vibration detection The device can be set to send an alarm to the administrator's phone number in an SMS message when it is moved or vibration is detected. To activate or deactivate the motion / alarm detection mode, the following SMS commands must be sent to the device: Turning on Send the command von,x# (vibration on) via SMS to the phone number of the device, where x can be 1,2,3 or 4 - these can be used to control the sensitivity of the sensor. If the device has received and executed the command, confirm it by sending an SMS with OK. Turning off Send the command voff# (vibration off) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. Sound detection The device can also detect sounds and send an alarm. To turn the voice recognition mode on or off, send the following SMS commands to the device: Turning on Send non# (noise on) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. Turning off Send noff# (noise off) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK.
Tracking Position query When the GPRS mode is on, you can query the current position of your device. To do this: Send the following command via SMS to the phone number of the device's SIM card: url# The device sends the position data (latitude, longitude) in a reply SMS. Administrator phone number setting After setting the administrator phone number, the tracking device only accepts SMS commands from this number. SMS command: password,sos1,phone number# Example: 123456,sos1,06209876543 Device response: 06209876543 has been set for the master number successfully. SMS command to delete the phone number set above: reset# Switching LED indicators on and off The LED displays continuously show the network (GSM and GPS) connection status of the device with their light signals. If necessary - e.g. for energy saving reasons) - the operation of the LEDs can be switched on or off. Turning on Send the command lon# (led on) via SMS to the phone number of the device. If the device has received and executed the command, confirm it by sending an SMS with OK. Turning off Send loff# (led off) via SMS to the device's phone number. If the device has received and executed the command, confirm it by sending an SMS with OK. LED mode is on by default. Restart device remotely If you experience a problem with your device, a restart may resolve it. You can initiate the reboot remotely. Send reboot# via SMS to your device's phone number. Turn off the device remotely You can also switch the device on and off remotely from your phone. Send poff# (power off) via SMS to the phone number of the device. Set SMS language and time zone The language of SMS communication can be Chinese, English or French. This and the valid time zone can be set with the following command. Send lag,x,zone,y (language, timezone) via SMS to the device phone number, where x = 1 (Chinese), 2 (English) or 3 (French) and y = GMT + time offset value (+ or -), in hours. Example: lag,2,zone,+1 English language and the Hungarian time zone.
Lamp There is a built-in LED headlight at one end of the device. To switch it on or off, briefly press the on / off button on the device once.

Normal operation of the device

The device can be operated in the following ways:

using the software service provided by the distributor and the SIM card together, in addition to the software service provided by the distributor but using his own SIM card, or
without the service provider's software service, with your own SIM card.

The service provider provides a SIM card for the tracking device only if you subscribe to the software service. In the case of unsolicited use of the software, the user must provide the appropriate card with a data traffic limit (also).

With Distributor Software and SIM Card

In this case, you can receive the device in the ready state, no further settings are required to use it.

Separate software is available for setting or adjusting the operating parameters of the device, for retrieving information or for using more advanced services (eg map route display, waiting and travel points, diagrams, timetable, etc.). This is provided by the distributor in the form of a downloadable application on a desktop and tablet browser on an Android mobile phone as part of a subscription system.

To use the software, an active internet connection is required on your device (mobile phone, computer).

The software stores and processes the data sent by the tracking device to the service provider's center, from which the graphical and textual information is generated. Using the software triggers (sometimes very expensive) SMS and voice call communication with the device and provides tracking and security services that go well beyond the basic functions of the device.

After launching the application in a browser or phone:

In the login window, enter the username and password you received in the email from the distributor or registered on its website.
In the interface that appears, select Help and review the information for using the software.
Software management information is available in its help.

With Distributor software but with own SIM card

After setting up and inserting the SIM card as described in the setup chapter, you must register the card. To do this, contact your software service provider (device vendor). From now on, the operation of the device is the same as described in the previous chapter.

Without software, with own SIM card

If you have subscribed to the reseller's software service, DO NOT use the standalone SMS communication method because

redundant (the software has all the functions needed for tracking and settings),
the software provider charges a separate fee for the possible elimination of possible operational anomalies caused by SMS commands,
if you use your own SIM card in the device, SMS will incur extra costs,
if you use your service provider's SIM card, your service provider will reimburse you for the cost of the SMS.

If you do not use (have not subscribed) to the software service provided by the dealer, you can only use the basic functions of the device - by sending SMS messages from your mobile phone to the phone number of the device's SIM card.

Setting options via the software

When using the desktop or mobile application of Flexcom Kft, the setup operations related to tracing can be accessed in the following ways.

The settings and commands that can be issued depend on the type of device. See the rest of this guide for information on options for this device.

When using a desktop application:

Select the desired device on the map or in the menu. Click the Settings or Commands button to select the general setting or behavior you want.

When using a mobile application:

From the application menu, select Map.
Switch to the Tools panel.
Find your device in the list of devices and tap the Setup icon next to the ID.
Select the desired setting or, when sending a command, select Commands.